The SPOOLOGIC Upgraded Compressor Housing Kit 63.5mm 11-Blade Billet Wheel SL-230-010 is a complete wheel-plus-housing PowerMax-spec upgrade kit for 2003-2010 Ford 6.0L Powerstroke applications. It pairs an 11-blade billet aluminum compressor wheel with a matched PowerMax-spec compressor housing so the wheel, housing, backing plate, and sealing hardware all work together as a single clean upgrade. CNC-machined wheel: 63.5mm inducer, 88mm exducer base, 94mm extended-tip outer diameter, 11 full blades (no splitter blades). Sold as a kit because the wheel will not clear a stock factory 6.0L cover.

Why Extended-Tip Exducer

Extended-tip technology lets a smaller wheel perform like a larger one. The blade tips extend past the back face of the exducer, increasing effective blade area without enlarging the inducer or compressor housing. Benefits versus a flat-tip wheel of the same base dimension:

• Greater airflow at the same shaft speed (more CFM per RPM)
• Faster boost response at lower engine speeds
• Higher peak pressure ratio and broader compressor map width
• Lower EGTs at cruise and under load from more efficient compression
• Improved high-RPM efficiency without losing low-end response

Why Billet Over Cast

• Forged aluminum billet has 15-25% higher yield strength than cast aluminum, allowing aggressive blade and tip geometry that would fail in cast form
• Thinner, more refined blade profiles reduce rotational mass for quicker spool-up
• Denser, aligned grain structure resists crack initiation and high-cycle fatigue
• Better foreign-object-damage tolerance — small debris nicks rather than fractures
• Higher safe tip speed allows the wheel to live behind aggressive tunes and added fueling

Drop-In Upgrade for Stock 6.0L Turbos

This kit solves the stock-cover problem. The bare SPOOLOGIC SL-220-014 and SL-220-015 wheels fit Garrett PowerMax service turbochargers only because their 63.5mm inducer and extended-tip outer diameter will not clear a factory stock 6.0L compressor cover. This kit includes the correct PowerMax-spec compressor housing pre-matched to the wheel, so you can convert a stock 6.0L turbo to PowerMax-spec airflow without sourcing a separate housing or machining the factory cover.

• Bolt-on for trucks running the factory stock 6.0L Powerstroke turbo
• Also bolts onto an existing PowerMax assembly as a complete cover-plus-wheel refresh
• No compressor cover machining required — the housing comes pre-machined to the correct PowerMax wheel-to-housing clearance
• If you already own a PowerMax compressor housing, order the wheel by itself — SL-220-014 for the 6+6 wheel or SL-220-015 for the 11-blade wheel
• Pair with SPOOLOGIC SL-210-003 for the matching CHRA rebuild kit (bearings, seals, and hardware)

What’s Included

• (1) SPOOLOGIC SL-220-015 63.5mm 11-blade billet compressor wheel
• (1) PowerMax-spec compressor housing
• (1) Backing plate
• (1) Compressor wheel lock nut
• Sealing O-rings — set
• Mounting bolts — set

Wheel Specs

• Inducer: 63.5mm
• Exducer: 88mm base diameter, 94mm extended-tip outer diameter
• Blade configuration: 11-blade (11 full blades, no splitters)
• Material: 5-axis CNC-machined forged billet aluminum
• Profile: Extended-tip PowerMax-spec geometry
• Thread: Left-hand (turns left to tighten against turbo rotation)
• Balance: Computer-balanced from the factory

Installation Procedure

This kit installs as a complete wheel and compressor housing swap on the GT3782VA / GT3788VA CHRA. The shaft nut is left-hand thread.

1. Remove the turbo from the truck
2. Remove the original compressor housing from the CHRA and discard if converting from a stock 6.0L cover
3. Hold the turbine wheel hub against rotation with a leather glove or soft-jaw method — never use an impact gun
4. Remove the factory compressor nut by turning it clockwise (left-hand thread) and pull the original wheel off the shaft
5. Inspect the shaft and threads for damage; clean thoroughly with brake cleaner
6. Slide the new SPOOLOGIC billet wheel onto the shaft, oriented with blades facing the inlet
7. Apply a small drop of blue threadlocker to the shaft threads
8. Thread the supplied lock nut on by turning counter-clockwise (left-hand thread) and torque to 10 ft-lb / 120 in-lb
9. Install the supplied backing plate onto the CHRA using new sealing O-rings
10. Install the supplied PowerMax-spec compressor housing onto the backing plate
11. Install and torque the supplied mounting bolts to OEM spec
12. Verify the wheel spins freely with no rub against the compressor housing before reinstalling on the truck

Features

• Complete wheel-plus-housing PowerMax-spec upgrade kit for 2003-2010 6.0L Powerstroke
• 63.5mm inducer × 88mm exducer base with 94mm extended-tip outer diameter
• 11-blade configuration (11 full blades, no splitters) for high airflow and high-RPM efficiency
• Includes matched PowerMax-spec compressor housing — no stock cover machining required
• Backing plate, sealing O-rings, lock nut, and mounting bolts all included
• Bolt-on upgrade for trucks running the factory stock 6.0L turbo or an existing PowerMax assembly
• CNC-machined wheel from forged 2618-class aluminum billet, computer-balanced
• Higher airflow and faster spool than the OE PowerMax wheel

Fits 2003-2010 6.0L Powerstroke

• 2003 – 2007 Ford F-250 / F-350 / F-450 / F-550 Super Duty 6.0L Powerstroke
• 2004 – 2010 Ford E-350 / E-450 / E-550 Econoline 6.0L Powerstroke
• 2003 – 2005 Ford Excursion 6.0L Powerstroke

Replaces Factory OEM Part Numbers

• Garrett: 777469-5002S
• Garrett: 772441-5002S

⚠ Not For Sale In California

Emissions Notice: Not CARB approved. Not legal for sale or use in the state of California.

DIY Product — All Sales Final, No Warranty, No Returns

This SPOOLOGIC compressor housing kit is a professional DIY assembly product intended for experienced turbo builders and rebuild shops. Successful installation requires proper tools, OEM service procedures, cleanliness standards, correct left-hand shaft nut torque to 10 ft-lb / 120 in-lb, and verification that the compressor wheel spins freely with no housing contact before running the turbo. Because SPOOLOGIC cannot control installation quality, all sales are final — no warranty, no returns, no exchanges. By purchasing this product you acknowledge that you are responsible for correct installation, torque, clearance verification, and assembly.